Skip to content
Skip to content

Parts

The same part is cleaned across several industries. Browse by what the part IS — its geometry and its material decide the frequency and the process.

Close-up of printed circuit board traces and solder pads

Ultrasonic cleaning by workpiece

Moulds, dies and tooling

Moulds and dies are cleaned to a cosmetic standard, not just a functional one: whatever is left in the cavity is reproduced on every part that follows. The soils are baked-on release agent, resin and gas residue in vents and textures that a brush cannot reach without polishing the tool.

28 / 40 kHz
Learn more

Precision machined parts

Turned, milled and drilled parts arrive carrying the fluid they were cut with, plus the swarf that fluid held against the metal. Blind holes, cross-drillings and thread roots are where it stays, and they are the geometry a spray simply travels past.

40 kHz
Learn more

Optics, glass and lenses

Optical surfaces are judged by what light does to them, so a residue too thin to see still fails the part. The usual soils are blocking pitch and wax from fabrication and cerium or alumina polishing slurry driven into the edge and the bevel.

40 / 80 kHz
Learn more

PCBs and electronic assemblies

Boards and populated assemblies are cleaned to remove flux residue that stays chemically active after soldering. The residue that matters is the residue you cannot see — under BGAs, beneath chip components and inside connector housings, where a spray stops at the first obstruction.

40 / 80 kHz
Learn more

Nozzles, jets and spinnerets

A nozzle is a calibrated hole, so cleaning it is dimensional work: the bore must come back open without being opened further. The blockage is usually carbonised — coked fuel, cured resin or thermally degraded polymer — and it is bonded to the wall rather than sitting on it.

28 / 40 kHz
Learn more

Wafers and semiconductor parts

Semiconductor parts are cleaned against a particle count, not an appearance. Nothing dissolves a particle, so removal is mechanical — and the cavitation that removes it is the same cavitation that can damage a polished face, which is why this family sits at the high-frequency end of the range.

80 / 120 kHz
Learn more

Bearings, gears and rotating parts

Rotating assemblies are cleaned before they are packed with their working lubricant, so the requirement is that the old grease and the wear debris in it are gone rather than redistributed. Cages, raceways and tooth roots hold both.

40 kHz
Learn more

Additively manufactured parts

Printed parts leave the machine still carrying the medium they were built in — uncured resin, loose powder or soluble support. Because the geometry is usually the reason the part was printed at all, the trapped material sits in internal channels and lattices that no line of sight reaches.

28 kHz
Learn more

Surgical and dental instruments

Instruments are cleaned before they are sterilised, and cleaning is what makes sterilisation possible: soil left in a box lock or a lumen shields whatever is under it. Protein sets when heated, so this family is washed cool and washed early.

40 kHz
Learn more

Food-contact ware and moulds

Food-contact items are cleaned to a hygiene standard against soils that are baked on rather than merely deposited — caramelised sugar, polymerised fat and protein films that a dishwasher jet softens but does not lift out of a corner or a mould relief.

28 / 40 kHz
Learn more

Heat exchangers and engine parts

These parts fail by fouling: a passage that has narrowed no longer moves the heat or the fluid it was sized for. The deposits are scale, carbon and oil coke laid down over service, bonded hard, and inside tube bundles and cores that cannot be dismantled to reach.

28 / 40 kHz
Learn more

Stamped and formed parts

Stamped and drawn parts carry the forming lubricant that let them deform without tearing — a heavy, often waxy film that is solid at room temperature. It fails downstream at plating or coating rather than at assembly, which is why it is usually found late.

40 kHz
Learn more

Filters, screens and mesh

A filter is cleaned to restore flow, and it is the one workpiece whose whole function is to have collected contamination. Cleaning has to clear the pore without deforming the mesh or the pleat that defines its rating.

28 / 40 kHz
Learn more
Request a Quote

Tell us what you need cleaned

Send us the part, the contaminant and your cycle time. Our engineers size the tank, the frequency and the process chain — and reply with a sized specification for your line.

LINEPhoneRequest a Quote